CSEC Mathematics · vectors and matrices
Direction of a Vector
Before you start
A vector written as a column matrix (xy) or in component form xi+yj represents a displacement of x units horizontally and y units vertically.
Builds on: Position Vectors
1. Finding the Direction of a Vector in the First Quadrant
A vector has both magnitude (size) and direction. When drawn on a Cartesian grid, a column vector v=(xy) forms a right-angled triangle with the horizontal axis:
- The horizontal displacement x is the side adjacent to the angle θ.
- The vertical displacement y is the side opposite to the angle θ.
Using basic trigonometry (SOH CAH TOA):
To find the direction angle θ made with the positive x-axis:
For positive values of x and y, θ is an acute angle measured anticlockwise from the positive horizontal axis.
Worked example
A displacement vector is given by u=(64) km. Calculate the direction of u as an angle made with the positive horizontal axis, correct to 1 decimal place.
- Identify the components: horizontal x=6 and vertical y=4.
- Set up the tangent ratio: tanθ=xy=64=32.
- Take the inverse tangent: θ=tan−1(32)≈33.690∘.
- Round to 1 decimal place: θ=33.7∘.
Answer: The direction is 33.7∘ above the positive horizontal axis.
Quick check
Find the angle θ (in degrees) that the vector w=(55) makes with the positive x-axis.
2. Vectors with Negative Components
When a vector has negative components, it points into one of the other quadrants:
- Second quadrant (x<0,y>0): moves left and up.
- Third quadrant (x<0,y<0): moves left and down.
- Fourth quadrant (x>0,y<0): moves right and down.
To find the direction, always sketch a quick triangle using positive lengths ∣x∣ and ∣y∣ to find the acute reference angle α:
Then state the direction clearly, either by describing it relative to the horizontal (e.g. "21.8∘ above the negative horizontal axis") or by finding the standard anticlockwise angle from the positive x-axis:
- Second quadrant: 180∘−α
- Third quadrant: 180∘+α
- Fourth quadrant: 360∘−α (or −α)
Worked example
Vector a=(−52). Calculate the direction angle of a measured anticlockwise from the positive x-axis, to 1 decimal place.
- Draw or visualise the vector: x=−5 (left) and y=2 (up), placing it in the second quadrant.
- Find the acute reference angle α using positive lengths: tanα=52=0.4.
- Calculate α: α=tan−1(0.4)≈21.80∘.
- Since the vector is in the second quadrant, subtract α from 180∘: θ=180∘−21.80∘=158.2∘.
Answer: 158.2∘
Quick check
Which statement correctly describes the direction of the vector b=(4−3)?
3. Direction as a Three-Figure Bearing
In Caribbean real-world contexts, such as maritime navigation between Caribbean islands, direction is commonly stated as a bearing:
- Measured clockwise from North (000∘).
- Written using three digits (e.g. 045∘, 090∘).
When working on the grid:
- North corresponds to the positive y-direction.
- East corresponds to the positive x-direction.
For a displacement vector (xy) in the north-east direction (x>0,y>0):
Notice that this ratio is the reciprocal of the tangent of the angle with the x-axis (which uses xy)! A quick sketch with a North line guarantees you pick the correct angle.
Worked example
A fishing boat departs from a port in Castries and travels with displacement vector s=(724) km, where the components represent displacements East and North respectively. Find the bearing of the boat from the port to the nearest degree.
- Identify East (opposite to North line) = 7 km and North (along North line) = 24 km.
- The angle from North β satisfies tanβ=NorthEast=247.
- Calculate the angle: β=tan−1(247)≈16.26∘.
- Round to the nearest whole degree and write as a three-figure bearing: 016∘.
Answer: 016∘
Quick check
A patrol vessel has displacement vector (88) km (8 km East and 8 km North). What is the vessel's bearing from its starting position (in degrees)?
Common mistakes
- Inverting the tangent fraction: writing tanθ=yx instead of xy when finding the angle with the horizontal. Remember tan=adjacentopposite=xy.
- Confusing bearings with horizontal angles: angles with the horizontal are measured from the x-axis, whereas bearings are measured clockwise from North (y-axis).
- Ignoring negative signs in quadrant calculations: entering negative values into tan−1 without sketching the vector first, leading to negative angles or wrong quadrants.
In the exam
- Always state what your angle is measured relative to, for example: '36.9∘ to the horizontal' or as a bearing '037∘'.
- Show the formula tanθ=xy and substitution clearly before evaluating to secure method marks.
- Ensure your calculator is in DEG (degree) mode rather than RAD (radian) mode before doing inverse trigonometric calculations.
Key terms
- Direction of a vector
- The orientation of the vector line segment, typically expressed as an angle relative to a reference line (such as the positive horizontal axis or true North).
- Reference angle
- The positive acute angle made between the vector line and the horizontal axis, found using tan−1(∣y∣/∣x∣).
- Bearing
- A directional angle measured clockwise from North, written using three digits.
Practice
Easier to harder. Use paper for your working.
Practice 1
Vector p=(37). Calculate the angle that p makes with the positive x-axis, in degrees, to 1 decimal place.
Practice 2
Given points A(1,2) and B(5,5), find the direction of the displacement vector AB⃗ as an acute angle with the horizontal, correct to 1 decimal place.
Practice 3
A vector has components (−6−6). What is its direction measured anticlockwise from the positive x-axis?
Finished the lesson?
0 of 6 checks right on this device.
Read more
- Collins - Concise Revision Course for CSEC Mathematics, p. 439
- algebra-and-trigonometry-2e_-_WEB, pp. 984, 987
- precalculus-2e_-_WEB, p. 879